fbpx
Login

 

Jump to Forum..

Fun questions to stimulate and educate for the 912

in 912 / 914 Technical Questions 13 years ago

  • Re: Fun questions to stimulate and educate for the 912

    by » 13 years ago

    What is the integrated alternator output? answer: 12V 20A DC

    What do the crankshaft drive gear and the dog gear have in common? answer: These two have matching 6 digit serial numbers

    What does the cylinder head temperature sender measure? answer: It measures the metal temp

    What are the new spark plug gap settings? (.6mm -.7mm) .023 - .027 The wider gap is better for the hot OAT and the narrower is better for cold OAT

    How often should the coolant be replaced?
    answer: every 2 years. (I know there is a place where it says by overhaul, but that's rediculous since that may be 12-15 years away)


    Ok guys try some more.

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report

  • Re: Fun questions to stimulate and educate for the 912

    by » 13 years ago

    #1 1-4-2-3, .66 gal. in the can plus the oil cooler content, dry sump.
    #4 rpm counter.
    #5 crankcase pressure.
    #6 water cooled
    #7 912=1211 cm3, 912s=1352 cm3

    Maybe I'm better on these,

    Bill
      
    Report

  • Re: Fun questions to stimulate and educate for the 912

    by » 13 years ago

    What is the firing order for the Rotax 912? answer: 1423

    What is the oil content of a 912 engine? answer: 2.5 lts - 3 lts or .793 US gal or .66 - .8 gal. 3 qts. is just right on a oil change

    What type of oil sump is used on the 912? answer: dry sump

    What is the 5th trigger coil pickup used for? answer: tach / rpm pick up

    How is the oil returned from the crankcase to the oil tank? answer: crank case pressure

    How are the cylinder heads on the Rotax 912 cooled? answer: water cooled


    What is the cubic inch displacement of the Rotax 912? answer: 912UL=1211 cm3, 912ULS=1352 cm3

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report

  • Re: Fun questions to stimulate and educate for the 912

    by » 13 years ago

    #8 22-44 ft/lbs, 30-60nm
    #9 2.27/1
    #11 In the crossover tube (manifold equalizer tube)
    #12 NOT A CLUE
    #13 enrich the mixture

    can't find #12 anywhere

    Bill
      
    Report

  • Re: Fun questions to stimulate and educate for the 912

    by » 13 years ago

    10. What is the accepted gearbox friction torque, upper and lower limit? answer: 22-44 ft/lbs or 264-528 in/lbs or 30-60nm

    11. What is the gear reduction ratio for the 912S series? answer: 2.43:1 912S or ULS(2.27:1 is the normal 912A or UL 80 hp)

    13. Where on the engine is the manifold pressure taken? answer: on the aluminum carb balance tube, there is a little nipple more on the left side

    15. On the carb, lifting the jet needle from the second to the third notch will do what? answer: it will richen the mixture

    Roger Lee
    LSRM-A & Rotax Instructor & Rotax IRC
    Tucson, AZ Ryan Airfield (KRYN)
    520-349-7056 Cell

      
    Report
You do not have permissions to reply to this topic.
Related Topics
Title Category Replies
912is rpm drop 912iS Technical Questions 22
RPM Drop in 912ULS 912 / 914 Technical Questions 3
RPM Drop in 912ULS 912 / 914 Technical Questions 21
Torque 912 ULS 912 / 914 Technical Questions 7
912 Flydat wiring 912 / 914 Technical Questions 0
Follow Us

Recent Videos

Safety First!

 

To receive critical-to-safety information on your ROTAX Engine, please subscribe to
ROTAX-OWNER.COM

Prize Giveaway!


SUBSCRIBE NOW
to automatically enter this years draw!

Login