fbpx
Login

 

Jump to Forum..

Fuel Flow sensor Install

in General Tech Discussion 7 years ago

  • Re: Fuel Flow sensor Install

    by » 5 years ago

    I will get back to you tomorrow with more information.
      
    Report

  • Re: Fuel Flow sensor Install

    by » 5 years ago

    Ok thanks Bill I will fly tomorrow and record all the setting I get on the sensor and the dip stick readings.
    I will try unplugging the sensors tomorrow and let you know. AND hey thanks for all the help.
      
    Report

  • Re: Fuel Flow sensor Install

    by » 5 years ago

    Bill I flew today and recorded some data : at 2000 flow 6.9, 2500-7.5 4000-9.7 5200- 11.0 I tried to fly for one hour but screwed up and did not get the time off and on estimate 1hour 12min.

    I set the sensor fuel at 22 gallons when I returned the instrument said I used 13.6 gallons and had 8.4 left.
    I had the low fuel alarms set at 6 gallons and the alarm kept coming on at the end of the flight.

    When I dipped the tanks at the start the RIGHT tank 4.3/4 inch end 3.7/8 LEFT start 4.0 end 3.1/2 I have not added fuel yet to check how much I used. Its getting hot up here in the mountains so I don't want to add more fuel
    unless you need to know the amount I used but it looks like 5 or 6 gallons.
      
    Report

  • Re: Fuel Flow sensor Install

    by » 5 years ago

    Well, it is safe to say that the engine is NOT actually using more than 10gph.
    If you indicate 4.7gph Engine OFF and if we subtract that number from your data we get...

    2000rpm = 2.2gph
    2500rpm = 2.8gph
    4000rpm = 5.0gph
    5200rpm = 6.3gph

    That still seems a little high but more within reason. (Calibration Issue?)

    Assuming a rectangular fuel tank; 22gal - (22 x 3.88" / 4.75") ≈ 4 gallons.
    A reasonable number.

    You did not report the displaying with the senders disconnected but it appears you are displaying the Total Flow without subtracting the Return Flow.

    The objective at this point is to get the system to display ZERO Flow with the Fuel Pumps ON and the Engine OFF.
    I would look at the Installation/Configuration of the FP-5L

    Now the Big questions...
    Are you sure you have two senders?
    Are you sure they are FT-60s?
    How are they connected to the FP-5?

    I can find nothing online about how to connect an FP-5 to a fuel injected engine or any engine with bypass fuel flow for that matter.
    As far as I can see, it is a single sender computer.
    Can you post the installation documentation? (Not the Operators manual!)
    We need to see the wiring diagram.

    Bill Hertzel
    Rotax 912is
    North Ridgeville, OH, USA
    Clicking the "Thank You" is Always Appreciated by Everyone.

    Thank you said by: Robert Hannigan
      
    Report

  • Re: Fuel Flow sensor Install

    by » 5 years ago

    Ok I will look for the install manual. this unit was installed by someone else to provide fuel pressure for the injectors.
      
    Report
You do not have permissions to reply to this topic.
Related Topics
Title Category Replies
Fuel PSI sensor relocation hose 912 / 914 Technical Questions 2
fuel pump light 915iS Technical Questions 0
914 using only electric fuel pumps 912 / 914 Technical Questions 2
Need to find 912iS Fuel Filter General Tech Discussion 0
Need to find 912iS Fuel Filter General Tech Discussion 8
Follow Us

Recent Videos

Safety First!

 

To receive critical-to-safety information on your ROTAX Engine, please subscribe to
ROTAX-OWNER.COM

Prize Giveaway!


SUBSCRIBE NOW
to automatically enter this years draw!

Login